Free Help Setting up Your Router or Firewall Set up your router from home
Home Guides Reviews Store Support Forum Requests
see list of routers and firewalls below

Firewalling for the Agnitum Outpost Firewall Pro






 

Before we can open ports for Ares, we need to figure out what ports ares is using. Here is a brief walkthrough on how to do that.



Open up Ares. Then click the Control Panel icon in the toolbar at the top of your screen.



You should see a bunch of tabs close to the top of this window. One of these tabs should be labeled Transfer. Go ahead and click it now.



Enter the port you want Ares to use into the Accept incoming connections on port box. By default this port is set to 1157. You can change it to whatever you like, or leave it set to 1157.

Please enter the port you chose for Ares below.

Ares' Port

Open up Ares.


You might see a window pop up like the one above. If you do, put a dot in to the Allow all activities for this application radio button, and click the Ok button. If you try modifing the permissions for Ares with it open, you will get popup windows while trying to make your changes. So it's best to close Ares. Go ahead and do that now. Then go aheand and open up the Agnitum Outpost Firewall Pro.


Click Options in the menu at the top of your screen. Then click the Application link in the submenu that drops down.


Now you should be looking at a window that displays a list of applications that you have on your computer. Find Ares and right click it. Click the Create Rules or the Modify Rules link depending upon what show up in that list.


Go ahead and remove all the rules that are listed here. When you are done adding the rules shown on this page, be sure to look at the outgoing guides and add those rules as well. If Ares is not listed in the outgoing guides, create a rule that allows all outbound traffic for Ares.We are going to show you exactly how to configure the Lavasoft firewall from here on out. So you should make the screens look exactly like they do in this guide.
Click the New button on the right hand side of this window.
Rules
 
Select Event, then Action and then specify the Rule Description.
 
  1. Select Event the rule will handle:
Where the specified protocol is
Where the specified direction is
Where the specified remote host is
Where the specified remote port is
Where the specified local port is
Where the specified time interval is
Where the local port is equal to the remote port
  2. Select Actions the rule will respond with:
Allow it
Block it
Report it
Run application
Stateful Inspection
Ignore Compontent Control
  3. Rule Description {click on an underlined value to edit it}
Where the specified protocol is Undefined
Where the specified direction is Outbound
Where the local port is Undefined
  4. Rule Name
Outbound TCP for Ares1
 


You will not be able to put a checkmark in to the Where the specified local port is checkbox until you complete the following step. Click the Where the specified protocol is Undefined link, and you should see the following window.

Select Protocol
 
Select protocol:
TCP
UDP
 


Click the Ok button to save your selection. Now go put a checkmark in to the Where the specified local port is checkbox. Click the and Where the direction is Outbound link, and change the direction to Inbound. Then click the and Where the local port is Undefined link.

Select local port
 
Port alias:
 
Enter the port number or port range, seperated by commas.
Example: 1, 3, 5-12
 


Click the Ok button to apply those changes. You should now be back at the rules page and it should look like the following.

Rules
 
Select Event, then Action and then specify the Rule Description.
 
  1. Select Event the rule will handle:
Where the specified protocol is
Where the specified direction is
Where the specified remote host is
Where the specified remote port is
Where the specified local port is
Where the specified time interval is
Where the local port is equal to the remote port
  2. Select Actions the rule will respond with:
Allow it
Block it
Report it
Run application
Stateful Inspection
Ignore Compontent Control
  3. Rule Description {click on an underlined value to edit it}
Where the specified protocol is TCP
Where the specified direction is Inbound
Where the local port is 100000
  4. Rule Name
Inbound TCP for Ares1 from 100000
 
Click the Ok button to save that rule.
Click the New button on the right hand side of this window.
Rules
 
Select Event, then Action and then specify the Rule Description.
 
  1. Select Event the rule will handle:
Where the specified protocol is
Where the specified direction is
Where the specified remote host is
Where the specified remote port is
Where the specified local port is
Where the specified time interval is
Where the local port is equal to the remote port
  2. Select Actions the rule will respond with:
Allow it
Block it
Report it
Run application
Stateful Inspection
Ignore Compontent Control
  3. Rule Description {click on an underlined value to edit it}
Where the specified protocol is Undefined
Where the specified direction is Outbound
Where the local port is Undefined
  4. Rule Name
Outbound UDP for Ares2
 


You will not be able to put a checkmark in to the Where the specified local port is checkbox until you complete the following step. Click the Where the specified protocol is Undefined link, and you should see the following window.

Select Protocol
 
Select protocol:
TCP
UDP
 


Click the Ok button to save your selection. Now go put a checkmark in to the Where the specified local port is checkbox. Click the and Where the direction is Outbound link, and change the direction to Inbound. Then click the and Where the local port is Undefined link.

Select local port
 
Port alias:
 
Enter the port number or port range, seperated by commas.
Example: 1, 3, 5-12
 


Click the Ok button to apply those changes. You should now be back at the rules page and it should look like the following.

Rules
 
Select Event, then Action and then specify the Rule Description.
 
  1. Select Event the rule will handle:
Where the specified protocol is
Where the specified direction is
Where the specified remote host is
Where the specified remote port is
Where the specified local port is
Where the specified time interval is
Where the local port is equal to the remote port
  2. Select Actions the rule will respond with:
Allow it
Block it
Report it
Run application
Stateful Inspection
Ignore Compontent Control
  3. Rule Description {click on an underlined value to edit it}
Where the specified protocol is UDP
Where the specified direction is Inbound
Where the local port is 100000
  4. Rule Name
Inbound UDP for Ares2 from 100000
 
Click the Ok button to save that rule.
That should be it. The firewall should be properly configured.